Collet Chuks

Mars-Tech BT30 Er11a-70l,100l Er Coll... ₹ 1,505.00

BT30 Er11a-70l,100l Er Collet Chuck BT30 Tool Holder accepts all ER11 colletsThread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micronAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm Rear thread for pull stud is M12 X 1.75 All holders have capability to become through coolant by simply removing screw in the center by allen key

Sold out

BT50 fmb 22X250 LONG mm Face milling holder arbour pack of 1

Mars-Tech BT50 fmb 22X250 LONG mm Fac... ₹ 6,700.00

BT50 facemill holder also called facemill arbour and facemill adaptor BT50 FMA22 Is mainly used to hold Modular Indexable Cutter with Internal hole of 16 mm any cutter can come with a 22 mm Internal thread but normally 50 mm AND 63 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 50MM,100MM,150MM,200MM,250MM,300MM

Hydro Grip holder and 5 collets 6,8,10,12,16 mm

BT40 90L ID20MM Hydro Grip holder and 5 collets

HARLINGEN BT40 90L ID20MM Hydro Grip ... ₹ 24,544.00

BT40 90L ID20MM Hydro Grip holder and 5 collets 6,8,10,12,16 mm set pack of 1HARLINGEN BRAND Hydrogrip balanced upto 25000 rpm 20 mm inside id which can fit a 20 mm shank directly and for shorter shanks use a reduction sleeve 5 SLEEVES ARE WITH THIS Dia - 6,8,10,12,16

Mars-Tech BT40 CBK 5- 95/125/155/185 ... from ₹ 2,166.00

BT40 CBK 5- 95/125/155/185 Long pack of 1LBK also Called CBK is used for holding of SDJ EWN RBH kind of boring holders it has diffrent lengths to choose from variation balanced upto 12000 RPM

Mars-Tech ABT40 ER25um collet chuck 7... from ₹ 3,128.00

ABT40 ER25um collet chuck 70/100/150LABT40 HOLDER CAN FIT INTO BBT40 CALIBRATED SPINDLE ONLY. ABT40 Holder Taper and Both Faces Are in Contact With Spindle Due to Which Spindle and Holder Act as Single Unit This Allows a Higher "Radial Rigidity" Hence We Get Good Surface Finish and Dimensional Accuracy While Machining Also Low Vibration at Higher Speed Which Increases Tool Life Collet Chuck Holder Is Balanced to G6.3-12000 Rpm

KTA Kta kbt40 sla Holder sla25 ... ₹ 4,062.00

BBT40 Holder Taper and Both Face are in Contact with Spindle due to Which Spindle and Holder act as Single Unit this allows a Highter " Radial Rigidity" hence we get good surface finish and dimensional accuracy while maching also low vibration at highter speed which increase tool life. So These are better than general BBT40 Holders but it should only be used with BBT40 Calibarated Spindle Only. Side Lock Holder Is Balanced to G6.3-15000 RPM

Mars-Tech BT30 Er20a-70L,100L Er Coll... ₹ 1,505.00

BT30 Er20a-70L,100L Er Collet ChuckBT30 Tool Holder accepts all ER20 collets ER20 Collets range from 1 mm to 14 mm The thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityThe gage length is 70mm,100MMRear thread for the pull stud is M12X1.75

Mars-Tech ABT40 ER20A collet chuck 70... ₹ 3,128.00

ABT40 ER20A collet chuck 70/100LABT40 HOLDER CAN FIT INTO BBT40 CALIBRATED SPINDLE ONLY. ABT40 Holder Taper and Both Faces Are in Contact With Spindle Due to Which Spindle and Holder Act as Single Unit This Allows a Higher "Radial Rigidity" Hence We Get Good Surface Finish and Dimensional Accuracy While Machining Also Low Vibration at Higher Speed Which Increases Tool Life Collet Chuck Holder Is Balanced to G6.3-12000 Rpm

Mars-Tech ISO 40 keyless drill chuck ... ₹ 1,914.00

This arbor is commonly used for holding JT6 male taper like used in KEYLESS DRILL CHUCK

Jaibros Sk40 Morse Taper Adaptor Mt... ₹ 1,685.00

SK40 Morse Taper holder are used to hold Tang type shanks SK40 morse taper Is mainly used to hold Tang Type Drills and Arbours Better shank taper - accurate, rigid toolholder-to-spindle mount Less tool wear and replacement - less scrap Fully ground flange and V-groove, easy on the tool changers for less spindle and changer maintenance Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundRear thread for pull stud is M16 X 2.0

Mars-Tech BT30 FMB 32 face milling Ho... ₹ 1,505.00

BT30 FMB 32 face milling Holder ArbourBT30 face mill holder also called face mill arbour and face mill adaptor BT30 FMA32 Is mainly used to hold Modular Indexable Cutter with an Internal hole of 16 mm any cutter can come with a 32 mm Internal thread but normally 100 mm AND 125 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 60MMRear thread for pull stud is M12X1.75