Accessories

SCODAK Torque control torx key bit T6/T8/T15 pack of 1

SCODAK SCODAK Torque control torx ... ₹ 566.00

THESE BITS CAN ONLY BE USED WITH SCODAK torque control screw driver. you will get 1 pc of bit

Sold out

Mars-Tech ER20 um SPANNER TYPE pack of 1 ₹ 457.00

ER20UM Spanner for ER20UM regofix type nut , tighten it and loosen it

Sold out

Mars-Tech ER16 um SPANNER TYPE pack of 1 ₹ 445.00

ER16UM Spanner for ER16UM regofix type nut , tighten it and loosen it

Sold out

Mars-Tech MAZAK SK40 Pull Stud With H... ₹ 181.00

Mazak SK40 Pull stud used in CNC machines for BT40 holders ISO standard name is MAS403 Pull studs are an important link between machine and tool. The requirements concerning accuracy, rigidity and reliability are very high. Pull studs of minor quality not only decrease the performance of the machine, they are even a safety risk. A breaking pull stud might cause severe damage on machine and workpiece and even injuries on persons. made of special steel for higher rigidity proper heat treated ,

JIS7388/2/B-1983 PULL STUD special size pack of 1

Mars-Tech JIS7388/2/B-1983 PULL STUD ... ₹ 300.00

This is a special pull stud kindly check 2nd image for technical details

Sold out

SCODAK Torque control torx key T15 pack of 1

SCODAK SCODAK Torque control torx ... ₹ 3,304.00

Torque control key is used for saving from over tightening of screw This is T15 size comes with 2 bits long and short for T15

Sold out

SCODAK Torque control torx key T8 pack of 1

SCODAK SCODAK Torque control torx ... ₹ 3,304.00

Torque control key is used for saving from over tightening of screw This is T8 size comes with 2 bits long and short for T8

T type edge finder 10x28 mm mechanical pack of 1

Mars-Tech T type edge finder 10x28 mm... ₹ 961.00

Disc diameter is 28 mm and rod attached is 9 mm , holding dia is 10 mm Mechanical Edge Finder also called touch point sensor are used for find Zero point of the workpiece and find center of the hole.

Mechanical Ceramic Edge Finder ceramic 10x10 MM pack of 1

Mars-Tech Mechanical Ceramic Edge Fin... ₹ 1,023.00

ceramic edge finder for magnetic componenet as ceramic is non magnetic Mechanical Edge Finder also called touch point sensor are used for find Zero point of the workpiece and find center of the hole.

Ultra Precision Screw 4x15 T20mm long Pack of 10 nos.

Mars-Tech Ultra Precision Screw 4x15 ... ₹ 295.00

These are best ultra precision screw of MARS-TECH compare to any brand in the market

Ultra Precision Screw 3x7mm long Pack of 10 nos.

Mars-Tech Ultra Precision Screw 3x7mm... ₹ 295.00

These are best ultra precision screw of MARS-TECH compare to any brand in the market

Mars-Tech BT50 to ISO50 Adapter ₹ 630.00

The BT50 to ISO50 Adapter allows the machinist to use the same CNC holder in a conventional ISO0 machine by simply changing the retention knob/pull stud for this cheap but effective adapter. So instead of buying a new holder, you just purchase the OTT retention knob/pull stud and exchange the pull stud to convert the holder from BT50 to a standard SK holder for a conventional machine. REAR THREAD M24

Mars-Tech ER 50 COLLET DIA 32 PACK OF 1 ₹ 1,866.00

The standard ER collet is the most widely used clamping system in the world.Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding. Unless specified differently all of our ER collets feature runout of 0.010 micron or less. ,ER collet sizes start at ER8 through ER50. ER50 series collets have a capacity of 6mm-34mm. Each ER50 collet has a range of (2 mm). The size indicated on the collet is the largest size it can hold and can be collapsed smaller within its collapse range of (1.8mm). For example, ER50-32mm can grab a round shank from 32mm diameter to 30.2mm diameter.

SCODAK Torque control torx key T6 pack of 1

SCODAK SCODAK Torque control torx ... ₹ 3,304.00

Torque control key is used for saving from over tightening of screw This is T6 size comes with 2 bits long and short for T6

Mars-Tech 3D TEST FINDER FOR all 3 ax... ₹ 49,560.00

3D TEST FINDER FOR all 3-axis Germany make 12mm shank pack of 1Made in Germany 3D tester for all 3-axis connect with us to know more about the product guarantee and usability it can save lots of time to take offset and many more features. https://www.youtube.com/watch?v=T1vXCwSBZWs Benefits- Ultra-slim design.- Waterproof: IP67- Robust & non-magnetic probe tips- Operates in the X, Y, and Z directions at the same time- Quick and easy to adjust thanks to new alignment technology- Mechanical end stops to protect the measurement unitApplicationIts precise and varied applications enable quick and simple identification of workpiece zero points and length dimensions. As soon as the indicators show "0", the spindle axis is located precisely on the workpiece edge.

Mars-Tech ABT40 locking device Tool B... ₹ 2,347.00

ABT40 locking device Tool Boy , ABt40 fixture clamping fixture of ABT40 pack of 1ABT40 Locking device with Vertical and Horizontal mode to tighten Nut and Pull stud made of Steel and long life. cone for taper is made of aluminium . 3.5 kgs of 1 pc.

Sold out

Jaibros TAP COLLET ER40 ₹ 1,204.00

ER TAP COLLETS ARE SIMILAR LIKE ER COLLETS AND CAN FIT INTO SAME COLLET CHUCK USED FOR ER COLLETS, BUT IT DOES NOT HAVE COLLAPSIBILITY AND EVERY COLLET COME FOR A FIXED SIZE. EVERY TAP HAS A SQUARE AND ROUND SO YOU JUST NEED TO CHECK SQUARE AND ROUND SIZE OF TAP AND ER CHUCK SIZE THAN YOU CHOOSE WHAT COLLET WILL FULFILL YOUR PURPOSE Tapping collets will allow user to convert collet chucks used for many purposes into tapping chucks. ER Tapping Collets with Square Drive for synchronous tapping operations using any RD/ER collet chuck. Collet bore is exact tool diameter, with square drive, for accuracy and rigidity. Square in the ER Tap collet is offer tight grip for Tap which reduces slippage in Collets. Available sealed for coolant-through applications, as well as in DIN and JIS standard metric sizes.

Sold out

Mars-Tech Tap Collet Er11 ₹ 782.00

Er Tap Collets Are Similar Like Er Collets and Can Fit Into Same Collet Chuck Used for Er Collets, but It Does Not Have Collapsibility and Every Collet Come for a Fixed Size.Every Tap Has a Square and Round So You Just Need to Check Square and Round Size of Tap and Er Chuck Size Than You Choose What Collet Will Fulfill Your Purpose Tapping collets will allow user to convert collet chucks used for many purposes into tapping chucks. ER Tapping Collets with Square Drive for synchronous tapping operations using any RD/ER collet chuck. Collet bore is exact tool diameter, with square drive, for accuracy and rigidity. Square in the ER Tap collet is offer tight grip for Tap which reduces slippage in Collets. Available sealed for coolant-through applications, as well as in DIN and JIS standard metric sizes.

Sold out

Mars-Tech HSK63 Tool holder fixuture ... ₹ 4,213.00

HSK63 locking device is made of Ductile cast iron and light in weight

Sold out

Mars-Tech ER Nut ER50UM Type Nut pack of 1

Mars-Tech Mars-Tech ER Nut ER50UM Typ... ₹ 1,143.00

Holds all ER50 collets from 6 mm to 36 mmMade from alloy steel hardened to 54 – 56rcPrecision ground ID thread and taperHas an id thread of – M64*2.0POutside diameter is 78 MMSUITABLE SPANNER IS ER50UM AND ER50 C TYPE key to tighteninginternal cam removes collet when unscrewedMARSTECH CODE IS ER50UM TYPE NUT