All

Tabikut 6 Mm Carbide Ballnose 55 HR... from ₹ 350.00

Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades. Bronze TiSiN Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing Flute Length of Ballnose is double of diameter if diameter is 1 mm flute length will be 2 mm same for other sizes , if total length increase flute length remain same of double of diameter.

Tabikut 3 mm Carbide Ballnose 55 HR... from ₹ 289.00

50 mm Length price is for 2 Nos. you order 1 quantity you will get 2 pcs 312 rs. price is for 2 nos. 1 will cost 156 rs. only. Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades. Bronze TiSiN Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing Flute Length of Ballnose is double of diameter if diameter is 1 mm flute length will be 2 mm same for other sizes , if total length increase flute length remain same of double of diameter.

Mars-Tech BT40ER16A collet chuck-70L,... from ₹ 1,250.00

BT40 Tool Holder accepts all ER16 collets ER16 Collets range from 1 mm to 12 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MM Rear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Jaibros Scriber Tip point tungsten ... ₹ 149.00

Steel pocket pen clip. Permanent magnet for picking up items (top end) Knurled Body for a Better Grip. Knurled Aluminium Tip is changeable easily ,Tungsten carbide pin point tip A carbide scribe may seem like an obscure tool, but it's not. What the carpenter's pencil is to building houses, the carbide scribe is to building with metal. As anyone who has marked metal will tell you, a pencil doesn't work and neither do most pens. If you can get a pen to make a line, it can easily be smudged off. Even the trusty Sharpie pen makes a big fat line. But a scribe is perfect. It marks a clean sharp line. And better still, it cuts through dirt, paint, rust, and mill scale. It's the tool to use for clean, accurate lines. Its secret is at the business end, a little sharpened rod of tungsten carbide, a material so hard it can even scribe a line on the surface of a tile. , and its tip is retractable As holds true with other things in life, when it comes to carbide scribes and metal working, little things mean a lot.

32 mm Indexable Inserted Endmill APMT1604

32 mm Indexable Inserted Endmill Dia 32 mm 3 Pocket Suitable To APMT1604

Mars-Tech 32 mm Indexable Inserted En... from ₹ 1,200.00

This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this Different Lengths and Different Shank size please choose before adding to cart BELOW IS A VIDEO FOR VIEW OF PRODUCT QUALITY AND BASIC DETAILS.

Mars-Tech Keyless Drill Chuck 1-13mm ... ₹ 1,448.00

MARS-TECH Heavy Duty Keyless Drill chucks are used for CNC machining center and milling machine Special Designed & manufactured against for super heavy torque use. Owning to inspecting strictly & with excellent RUNOUT accuracy and Quality guaranteed the gripping power double than general brand Avoid the drill dropped when used in instaneous change of direction and equipped with spanner hole for tightening prefect safety. Accuracy 50 mm Length within 0.05mm Spanner is optional not included with chuck. YELLOW TIATNIUM COATED JAWS FOR LONG LASTING LIFE.

BAP400R-50-22-4T Face Milling Cutter Dia 50 Modular Type Suitable To APMT1604 Insert Bull Cutter

Mars-Tech BAP400R-50-22-4T Face Milli... ₹ 1,080.00

Dia 50 cutter for APMT1604 insert , facemill cutter 50 mm apmt1604 Shank Holder FMB-22 This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use APMT1604 Of Tabikut Brand Insert into this , If any other brand have same insert it can also fixed to this. there are many Chinese brand also making same inserts so you can just check description of size from other brands to fix this insert. HAVE A VIDEO VIEW BELOW WITH BASIC DETAILS

Mars-Tech 14 mm Indexable Endmill Sui... ₹ 800.00

This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this

Tabikut TABIKUT Carbide Insert APMT... ₹ 850.00

WE SELL ORIGINAL INSERTS ONLY APMT1135 xmTABIKUT T20 Carbide insert for Steel and Stainless Steel machining with or without coolant , used in any suitable cutter for BAP300R and this is used in milling machine mainly. Suitable cutter any cutter which suits APMT1135 insert.For steel , mild steel , hrc upto 45 with coolant.APMT1135 for BAP300R cutters brown coatedSUITABLE TO ALL MILLING CUTTER FOR APMT1135

Grey Torx Screw 4mm 10/12 Mm Long Pack Of 100

Mars-Tech Grey Torx Screw 4mm 10/12 M... ₹ 399.00

Grey Torx Screw are also normal screw quality its just a grey coating Hardened Star Torx Screw for Milling Cutters offered are screws that come with precision design and constructed standards ,These torx screw are hardened upto 50-55 hrc for wear resistance, These Torx screw are mainly used in indexable tools as Boring bar , Insert cutter , milling cutter ,They are precise screw for better grip of carbide insert with pocket.

Grey Torx Screw 3.5 mm 8/9/10/12 Mm Long Pack Of 100

Mars-Tech Grey Torx Screw 3.5 mm 8/9/... ₹ 399.00

Grey Torx Screw are also normal screw quality its just a grey coating Hardened Star Torx Screw for Milling Cutters offered are screws that come with precision design and constructed standards ,These torx screw are hardened upto 50-55 hrc for wear resistance, These Torx screw are mainly used in indexable tools as Boring bar , Insert cutter , milling cutter ,They are precise screw for better grip of carbide insert with pocket

Tabikut TABIKUT APMT1604 T20 Carbid... ₹ 1,050.00

WE SELL ORIGINAL INSERTS ONLY APMT1604 T20 grade T20 Grade is for general soft machining and Carbide insert for Steel and Stainless Steel machining with or without coolant , used in any suitable cutter for BAP400R and this is used in milling machine mainly. Suitable cutter any cutter which suits APMT1604 insert.For steel , mild steel , hrc upto 45-55 with and without coolantAPMT1604 for BAP400R cutters brown coatedSUITABLE TO ALL MILLING CUTTER FOR APMT1604

Tabikut 1.5 mm Carbide Endmill 55 H... ₹ 290.00

Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades. Bronze TiSiN Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing

Mars-Tech Er32 Spanner wrench for ER ... from ₹ 190.00

ER32 UM and C Type Spanner Wrench is made from high quality alloy steel ,Thick material allows high torque without bending,4 point contact ensures no distortion of collet nut while tightening,ER32 Wrench works on all of our UM Type and UM type collet chucks that take ER32 collets

Mars-Tech Torx Screw 3.5 Mm T15 High ... ₹ 90.00

Hardened Star Torx Screw for Milling Cutters offered are screws that come with precision design and constructed standards ,These torx screw are hardened upto 50-55 hrc for wear resistance, These Torx screw are mainly used in indexable tools as Boring bar , Insert cutter , milling cutter ,They are precise screw for better grip of carbide insert with pocket

Tabikut 3 mm Carbide Endmill 45 HRC... ₹ 220.00

Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades. Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable

Mars-Tech BT40 locking device Tool Bo... ₹ 1,850.00

BT40 Locking device with Vertical and Horizontal mode to tighten Nut and Pull stud made of Steel and long life. cone for taper is made of aluminium . 3.5 kgs of 1 pc.

Mars-Tech Torx Screw 2.2 mm T6 ( Pack... ₹ 299.00

Hardened Star Torx Screw for Milling Cutters offered are screws that come with precision design and constructed standards ,These torx screw are hardened upto 50-55 hrc for wear resistance, These Torx screw are mainly used in indexable tools as Boring bar , Insert cutter , milling cutter ,They are precise screw for better grip of carbide insert with pocket

Mars-Tech BT40ER25UM- Collet Chuck 70... from ₹ 1,250.00

BT40 Tool Holder accepts all ER25 collets ER25 Collets range from 1 mm to 16 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MMRear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Mars-Tech ER 8 COLLET DIN6499B AA 0.... from ₹ 300.00

The standard ER collet is the most widely used clamping system in the world.Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding. Unless specified differently all of our ER collets feature runout of 0.010 micron or less. ,ER collet sizes start at ER8 through ER50. ER8 series collets have a capacity of 1mm-5mm. Each ER8 collet has a range of (0.5mm). The size indicated on the collet is the largest size it can hold and can be collapsed smaller within its collapse range of (0.5mm). For example, ER8-3mm can grab a round shank from 3mm diameter to 2.5mm diameter.

Find anything you need

GST Input Credit

7-Day Return

Lowest Prices

Highest Quality