Complete Range of Accessories
Holding Devices
BBT40 Holders Now Available
BBT40 Holders
Drills U Type
Mars-Tech
ABT40 HOLDER fmb22 different lengths
₹ 2,599.00
ABT40 Holder Taper and Both Face Are in Contact With Spindle Due to Which Spindle and Holder Act as Single Unit This Allows a Higher "Radial Rigidity" Hence We Get Good Surface Finish and Dimensional Accuracy While Machining Also Low Vibration at Higher Speed Which Increases Tool Life
So These Are Better Than General Bbt40 Holders but It Should Only Be Used With ABT40 Calibarated Spindle Only.
Collet Chuck Holder Is Balanced to G6.3-15000 Rpm
Mars-Tech
ABT40 SLA Holder abt40 side lock holder choose size from variation pack of 1
₹ 2,599.00
ABT40 Holder Taper and Both Face Are in Contact With Spindle Due to Which Spindle and Holder Act as Single Unit This Allows a Higher "Radial Rigidity" Hence We Get Good Surface Finish and Dimensional Accuracy While Machining Also Low Vibration at Higher Speed Which Increases Tool Life
So These Are Better Than General Bbt40 Holders but It Should Only Be Used With ABT40 Calibarated Spindle Only.
Collet Chuck Holder Is Balanced to G6.3-15000 Rpm
Mars-Tech
ABT40 Holder ABT40 ER32 diffrent lenghts
₹ 2,599.00
ABT40 Holder Taper and Both Face Are in Contact With Spindle Due to Which Spindle and Holder Act as Single Unit This Allows a Higher "Radial Rigidity" Hence We Get Good Surface Finish and Dimensional Accuracy While Machining Also Low Vibration at Higher Speed Which Increases Tool Life
So These Are Better Than General Bbt40 Holders but It Should Only Be Used With ABT40 Calibarated Spindle Only.
Collet Chuck Holder Is Balanced to G6.3-15000 Rpm
Mars-Tech
ABT40 Morse taper adator MT size
₹ 2,599.00
ABT40 Holder Taper and Both Face Are in Contact With Spindle Due to Which Spindle and Holder Act as Single Unit This Allows a Higher "Radial Rigidity" Hence We Get Good Surface Finish and Dimensional Accuracy While Machining Also Low Vibration at Higher Speed Which Increases Tool Life
So These Are Better Than General Bbt40 Holders but It Should Only Be Used With ABT40 Calibarated Spindle Only.
Holder Is Balanced to G6.3-15000 Rpm
Mars-Tech
U Drill 24MM
₹ 2,400.00
₹ 4,800.00
Please choose LXD of drill size as it can change drilling capacity which is most important part of drilling.
All Size comes in 2D 3D 4D 5D and Suitable Inserts SPMG AND WCMX please check from drop down menu .
Mars-Tech
U Drill 18mm
₹ 1,800.00
₹ 3,600.00
Please choose LXD of drill size as it can change drilling capacity which is most important part of drilling.
All Size comes in 2D 3D 4D 5D and Suitable Inserts SPMG and WCMX please check from drop down menu .
Mars-Tech
U Drill 16 mm
from ₹ 1,600.00
₹ 3,200.00
Please choose LXD of drill size as it can change drilling capacity which is most important part of drilling.
Diameter 13 mm to 17.5 mm comes in 2 shank 20 mm and 25 mm please select from drop down menu
All Size comes in 2D 3D 4D 5D and Suitable Inserts SPMG AND WCMX please check from drop down menu .
Mars-Tech
U Drill 19 MM
from ₹ 1,900.00
₹ 3,800.00
Please choose LXD of drill size as it can change drilling capacity which is most important part of drilling.
All Size comes in 2D 3D 4D 5D and Suitable Inserts SPMG AND WCMX please check from drop down menu .
Carbide Endmil & BallNose (45 to 60)
Original Korloy Inserts
Choose your Inserts by Application.
ER Collets & Tap Collets
Collets - ER Type
Collets - Tap
Mars-Tech
ER 32 COLLET DIN6499B AA 0.010 MICRON High Quality Precision Collet.
from ₹ 260.00
₹ 500.00
The standard ER collet is the most widely used clamping system in the world.Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding. Unless specified differently all of our ER collets feature runout of 0.010 micron or less. ,ER collet sizes start at ER8 through ER50.
ER32 series collets have a capacity of 1mm-20mm. Each ER32 collet has a range of (1 mm). The size indicated on the collet is the largest size it can hold and can be collapsed smaller within its collapse range of (0.9mm). For example, ER32-6mm can grab a round shank from 6mm diameter to 5.1mm diameter.
Mars-Tech
ER 16 COLLET DIN6499B AA 0.010 MICRON High Quality Precision Collet.
from ₹ 200.00
₹ 400.00
The standard ER collet is the most widely used clamping system in the world.Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding. Unless specified differently all of our ER collets feature runout of 0.010 micron or less. ,ER collet sizes start at ER8 through ER50.
ER16 series collets have a capacity of 1mm-12mm. Each ER16 collet has a range of (1 mm). The size indicated on the collet is the largest size it can hold and can be collapsed smaller within its collapse range of (0.9mm). For example, ER16-3mm can grab a round shank from 3mm diameter to 2.1mm diameter.
Mars-Tech
ER 25 COLLET DIN6499B AA 0.010 MICRON High Quality Precision Collet.
from ₹ 210.00
₹ 420.00
The standard ER collet is the most widely used clamping system in the world.Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding. Unless specified differently all of our ER collets feature runout of 0.010 micron or less. ,ER collet sizes start at ER8 through ER50.
ER25 series collets have a capacity of 1mm-16mm. Each ER25 collet has a range of (1 mm). The size indicated on the collet is the largest size it can hold and can be collapsed smaller within its collapse range of (0.9mm). For example, ER25-3mm can grab a round shank from 3mm diameter to 2.1mm diameter.
Mars-Tech
ER 20 COLLET DIN6499B AA 0.010 MICRON High Quality Precision Collet.
from ₹ 190.00
₹ 380.00
The standard ER collet is the most widely used clamping system in the world.Made from Alloy spring steel and fully hardened these ER collets are ideal for many machining applications including boring, milling, reaming, tapping and grinding. Unless specified differently all of our ER collets feature runout of 0.010 micron or less. ,ER collet sizes start at ER8 through ER50.
ER20 series collets have a capacity of 1mm-14mm. Each ER20 collet has a range of (1 mm). The size indicated on the collet is the largest size it can hold and can be collapsed smaller within its collapse range of (0.9mm). For example, ER20-3mm can grab a round shank from 3mm diameter to 2.1mm diameter.
Mars-Tech
ERG Tap Collets ERG32 Select Square And Round Pack Of 1
₹ 750.00
₹ 1,500.00
ER TAP COLLETS ARE SIMILAR LIKE ER COLLETS AND CAN FIT INTO SAME COLLET CHUCK USED FOR ER COLLETS, BUT IT DOES NOT HAVE COLLAPSIBILITY AND EVERY COLLET COME FOR A FIXED SIZE.
EVERY TAP HAS A SQUARE AND ROUND SO YOU JUST NEED TO CHECK SQUARE AND ROUND SIZE OF TAP AND ER CHUCK SIZE THAN YOU CHOOSE WHAT COLLET WILL FULFILL YOUR PURPOSE
Tapping collets will allow user to convert collet chucks used for many purposes into tapping chucks. ER Tapping Collets with Square Drive for synchronous tapping operations using any RD/ER collet chuck. Collet bore is exact tool diameter, with square drive, for accuracy and rigidity. Square in the ER Tap collet is offer tight grip for Tap which reduces slippage in Collets. Available sealed for coolant-through applications, as well as in DIN and JIS standard metric sizes.
Jaibros
TAP COLLET ER25
₹ 700.00
₹ 1,400.00
ER TAP COLLETS ARE SIMILAR LIKE ER COLLETS AND CAN FIT INTO SAME COLLET CHUCK USED FOR ER COLLETS, BUT IT DOES NOT HAVE COLLAPSIBILITY AND EVERY COLLET COME FOR A FIXED SIZE.
EVERY TAP HAS A SQUARE AND ROUND SO YOU JUST NEED TO CHECK SQUARE AND ROUND SIZE OF TAP AND ER CHUCK SIZE THAN YOU CHOOSE WHAT COLLET WILL FULFILL YOUR PURPOSE
Tapping collets will allow user to convert collet chucks used for many purposes into tapping chucks. ER Tapping Collets with Square Drive for synchronous tapping operations using any RD/ER collet chuck. Collet bore is exact tool diameter, with square drive, for accuracy and rigidity. Square in the ER Tap collet is offer tight grip for Tap which reduces slippage in Collets. Available sealed for coolant-through applications, as well as in DIN and JIS standard metric sizes.
Jaibros
TAP COLLET ER40
₹ 1,000.00
₹ 2,000.00
ER TAP COLLETS ARE SIMILAR LIKE ER COLLETS AND CAN FIT INTO SAME COLLET CHUCK USED FOR ER COLLETS, BUT IT DOES NOT HAVE COLLAPSIBILITY AND EVERY COLLET COME FOR A FIXED SIZE.
EVERY TAP HAS A SQUARE AND ROUND SO YOU JUST NEED TO CHECK SQUARE AND ROUND SIZE OF TAP AND ER CHUCK SIZE THAN YOU CHOOSE WHAT COLLET WILL FULFILL YOUR PURPOSE
Tapping collets will allow user to convert collet chucks used for many purposes into tapping chucks. ER Tapping Collets with Square Drive for synchronous tapping operations using any RD/ER collet chuck. Collet bore is exact tool diameter, with square drive, for accuracy and rigidity. Square in the ER Tap collet is offer tight grip for Tap which reduces slippage in Collets. Available sealed for coolant-through applications, as well as in DIN and JIS standard metric sizes.
Jaibros
TAP COLLET ER20
₹ 650.00
₹ 1,300.00
ER TAP COLLETS ARE SIMILAR LIKE ER COLLETS AND CAN FIT INTO SAME COLLET CHUCK USED FOR ER COLLETS, BUT IT DOES NOT HAVE COLLAPSIBILITY AND EVERY COLLET COME FOR A FIXED SIZE.
EVERY TAP HAS A SQUARE AND ROUND SO YOU JUST NEED TO CHECK SQUARE AND ROUND SIZE OF TAP AND ER CHUCK SIZE THAN YOU CHOOSE WHAT COLLET WILL FULFILL YOUR PURPOSE
Tapping collets will allow user to convert collet chucks used for many purposes into tapping chucks. ER Tapping Collets with Square Drive for synchronous tapping operations using any RD/ER collet chuck. Collet bore is exact tool diameter, with square drive, for accuracy and rigidity. Square in the ER Tap collet is offer tight grip for Tap which reduces slippage in Collets. Available sealed for coolant-through applications, as well as in DIN and JIS standard metric sizes.
Choose your Brand with 100% Genuine Guaranteed
Ballnose (45 HRC)
Endmill (45 HRC)
Tabikut
8 mm Carbide Ballnose 45 HRC 2flutes 60/100 Length PACK OF 1
from ₹ 374.00
Ballnose are 2 Flutes only
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating T478iALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable.
Pack of 1 means Qty. 1 Pack of 2 means price is for 2 nos.
Tabikut
6 mm Carbide Ballnose 2FLUTES/ 45 HRC PACK OF 2
₹ 418.00
BALLNOSE ARE 2 FLUTES ONLY.
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable.
Pack of 1 means Qty. 1 Pack of 2 means price is for 2 nos.
Tabikut
1 Mm Carbide Ballnose 2 flutes/ 45 Hrc Pack Of 2
₹ 248.00
BALLNOSE ARE 2 FLUTES ONLY.
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable.
Pack of 1 means Qty. 1 Pack of 2 means price is for 2 nos.
Tabikut
4 mm Carbide Ballnose 2FLUTES/ 45 HRC PACK OF 2
₹ 248.00
BALLNOSE ARE 2 FLUTES ONLY.
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable.
Pack of 1 means Qty. 1 Pack of 2 means price is for 2 nos.
Tabikut
3 mm Carbide Ballnose 2FLUTES/ 45 HRC PACK OF 2
₹ 248.00
BALLNOSE ARE 2 FLUTES ONLY.
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable.
Pack of 1 means Qty. 1 Pack of 2 means price is for 2 nos.
Tabikut
6mm Shank 3 Mm Ballnose In 2 Flutes (45HRC)
₹ 360.00
Carbide BALLNOSE 2 FLUTES 45 HRC
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Black Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing
Tabikut
4 mm Carbide Endmill 45 HRC PACK OF 2
₹ 220.00
₹ 400.00
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable
Tabikut
3 mm Carbide Endmill 45 HRC PACK OF 2
₹ 220.00
₹ 400.00
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable
Tabikut
2 mm Carbide Endmill 45 HRC PACK OF 2
₹ 220.00
₹ 400.00
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing
Tabikut
1 mm Carbide Endmill 45 HRC PACK OF 2
₹ 220.00
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing
ZCCCT
ZCCCT 4 MM CARBIDE ENDMILL 4 FLUTES ORIGINAL PACK OF 2
₹ 500.00
₹ 900.00
ZCCCT Carbide Endmill 4 MM 4 FLUTES 50 MM Long Original
ONLY 1 SIZE Available
Tabikut
1.5 mm Carbide Endmill 45 HRC PACK OF 2
₹ 220.00
Solid Carbide Cutter are used to machine Hard and tough Material , Steel , Alloy Steel , Cast iron , stainless steel and many other material grades.
Wine Coating TiALin Coating , Endmill for Better Life and wear resistance.35 Degree Helix Angel , Grain Size 0.5μmUsed for Face Mill , Shoulder mill , side mill etc ,Plastic Packaging for non breakable packing
Dasqua - Measuring Instruments
Inserted Endmill
Inserted Ballnose
Mars-Tech
16mm Indexable Inserted Endmill 2 Pocket Suitable To APMT1135, Choose different size from variation
from ₹ 500.00
₹ 1,000.00
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this
Different Lengths and Different Shank size please choose before adding to cart
Mars-Tech
20 mm Indexable Inserted Endmill Dia 20mm Shank19/20 mm 2 Pocket Suitable To APMT1135
from ₹ 750.00
₹ 1,600.00
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this
Different Lengths and Different Shank size please choose before adding to cart
Mars-Tech
12 mm Indexable Inserted Endmill BAP300R-C12-12-130-1T Suitable To APMT1135
from ₹ 510.00
₹ 880.00
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this
Mars-Tech
10 mm 1 pocket Indexable Inserted Endmill Dia 10 Suitable to APMT1135
from ₹ 499.00
₹ 800.00
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this
Mars-Tech
25 mm Indexable Inserted Endmill Shank25 Mm 3 Pocket Suitable To APMT1135
from ₹ 1,000.00
₹ 2,000.00
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of APMT1135 into this
Different Lengths and Different Shank size please choose before adding to cart
Mars-Tech
50 Mm Bull Cutter For Die And Mould Facing Cutter Suitable To RPmt1204 R6 Of Mostly Brand
from ₹ 950.00
₹ 1,800.00
EMRW-6R-50-22-4T suitable to R6 insert
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of RPMT1204/RDKW1204/R6 OF mostly brand into this ,
Recommended Suitable insert for this cutter is TABIKUT Carbide Insert
Mars-Tech
EMRW-C25-6R25-150L 25 Mm Bullnose Suitable To RPMT1204 Insert
from ₹ 1,000.00
₹ 2,000.00
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of RPMT1204/RDKW1204,R6 OF mostly brand into this , Suggested insert RPMT1204 OF Tabikut Brand.
Mars-Tech
80 Mm Bull Cutter For Die And Mould Facing Cutter Suitable To RPMT1204 R6 Of Mostly Brand
₹ 1,650.00
₹ 3,300.00
EMRW-6R-80-27-6T suitable to R6 insert
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of RPMT1204/RDKW1204/R6 OF mostly brand into this ,
Recommended Suitable insert for this cutter is TABIKUT Carbide Insert
Mars-Tech
63 Mm Bull Cutter For Die And Mould Facing Cutter Suitable To RPMT1204 R6 Of Mostly Brand
from ₹ 1,250.00
₹ 2,500.00
EMRW-6R-63-22-4T suitable to R6 insert
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of RPMT1204/RDKW1204/R6 OF mostly brand into this ,
Recommended Suitable insert for this cutter is TABIKUT Carbide Insert
Mars-Tech
50 Mm Bull Cutter For Die And Mould Facing Cutter Suitable To RDMT1204MOTN HITACHI brand
₹ 1,200.00
₹ 2,400.00
TRS-6R-50-22-4T suitable to hitachi R6 insert
This is Shoulder and Face Milling Cutter used mainly in CNC Milling and Manual Milling Machine with ISO Carbide Insert , Using this can reduce the cost really low compared to HSS and changing of insert time is also very low , They are hardened 45-50 HRC to not wear out , Pockets are well designed so insert and pocket seat have no gap in them , Run out tolerance is maintained by grinding by center to center and they have center hole both sides , you can use any ISO inserts of Hitachi Brand Insert RDMT1204 MOTN
Recommended Suitable insert for this cutter is TABIKUT Carbide Insert
Thanks for your Feedback on Facebook
Frequently Asked Questions
GST Input Credit
Get Business Invoice and get 100% GST Input Credit for your Order.7-Day Return
If you dont like the Product, Return it within 7 Days and get 100% refund.Lowest Prices
We are offering Products at Lowest Prices in the Industry*.Highest Quality
We strive to provide best quality product .