Mars-Tech

Mars-Tech BT40 fma16 mm face milling ... from ₹ 1,505.00

BT40 fma16 mm face milling holder arbourBT40 face mill holder also called face mill arbour and face mill adaptor BT40 FMA16 Is mainly used to hold Modular Indexable Cutter with an Internal hole of 16 mm any cutter can come with a 16 mm Internal thread but normally 40 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 70mm,100MM,150MM,200MM,250MM,300MMThe rear thread for the pull stud is M16 X 2.0

BT40 fmb 22 mm Face milling holder arbour pack of 1

Mars-Tech BT40 fmb 22 mm Face milling... from ₹ 1,505.00

BT40 facemill holder also called facemill arbour and facemill adaptor BT40 FMA22 Is mainly used to hold Modular Indexable Cutter with Internal hole of 16 mm any cutter can come with a 22 mm Internal thread but normally 50 mm AND 63 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 50MM,100MM,150MM,200MM,250MM,300MMRear thread for pull stud is M16 X 2.0

Mars-Tech BT40 fmb 40 mm Face millin... from ₹ 1,505.00

BT40 facemill holder also called facemill arbour and facemill adaptor BT40 FMA40 Is mainly used to hold Modular Indexable Cutter with Internal hole of 16 mm any cutter can come with a 40 mm Internal thread but normally 160mm AND 200 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 70MM,100MM,150MM,Rear thread for pull stud is M16 X 2.0

Mars-Tech BT40 JT6 Adaptor Holder For... ₹ 1,505.00

BT40 JT6 holders are mainly used to hold JT6 Female Taper , This holder have JT6 Male taper if anything like drill chuck have internal taper of JT6 so it can hold it easily with rigidity. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundRear thread for pull stud is M16 X 2.0

Mars-Tech BT40 locking device Tool Bo... ₹ 2,227.00

BT40 Locking device with Vertical and Horizontal mode to tighten Nut and Pull stud made of Steel and long life. cone for taper is made of aluminium . 3.5 kgs of 1 pc.

Mars-Tech BT40 Pull Stud In Various D... from ₹ 132.00

BT40 Pull stud used in CNC machines for BT40 holders ISO standard name is MAS403 Pull studs are an important link between machine and tool. The requirements concerning accuracy, rigidity and reliability are very high. Pull studs of minor quality not only decrease the performance of the machine, they are even a safety risk. A breaking pull stud might cause severe damage on machine and workpiece and even injuries on persons. made of special steel for higher rigidity proper heat treated ,

BT40 side lock adaptor , SLA 12 ,16,20,25,32,40 mm For Cylindrical Shank pack of 1

Mars-Tech BT40 side lock adaptor , SL... from ₹ 1,505.00

BT40 SLA holder also called SIDE LOCK HOLDER BT40 SIDE LOCK Is mainly used to hold Cylendrical/Straight Shank of anything like Indexable Cutter , Baby chuck , Carbide Drill whatever with straight shank can hold into for better rigidity and strength it range from 16 mm to 40 mm as small diameter of shank can be hold in standard collet chuck. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 50MM,100MM,150MMRear thread for pull stud is M16 X 2.0

Mars-Tech BT40 to ISO40 Adapter ₹ 481.00

The BT40 to ISO40 Adapter allows the machinist to use the same CNC holder in a conventional ISO40 machine by simply changing the retention knob/pull stud for this cheap but effective adapter. So instead of buying a new holder, you just purchase the OTT retention knob/pull stud and exchange the pull stud to convert the holder from BT40 to a standard SK holder for a conventional machine. REAR THREAD M16X2

Mars-Tech BT40ER16 collet chuck-70L,1... from ₹ 1,505.00

BT40 Tool Holder accepts all ER16 collets ER16 Collets range from 1 mm to 12 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MM Rear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Mars-Tech BT40ER20A-collet chuck 70L,... from ₹ 1,505.00

BT40 Tool Holder accepts all ER20 collets ER20 Collets range from 1 mm to 14 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MMRear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Mars-Tech BT40ER25UM- Collet Chuck 70... from ₹ 1,505.00

BT40 Tool Holder accepts all ER25 collets ER25 Collets range from 1 mm to 16 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MMRear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Mars-Tech BT40ER32 UM collet chuck-70... from ₹ 1,202.00

BT40 Tool Holder accepts all ER32 collets ER32 Collets range from 1 mm to 20 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MMRear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Mars-Tech BT40ER40 collet chuck UM-80... from ₹ 1,505.00

BT40 Tool Holder accepts all ER40 collets ER40 Collets range from 3 mm to 26 mm Thread inside internal stop screwMade from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundCoolant through capabilityGage length is 70mm,100MM,150MM,200MMRear thread for pull stud is M16 X 2.0 All holders have capability to become through coolant by simply removing screw in the center by allen key

Mars-Tech BT40fmb 27 mm Face milling ... from ₹ 1,505.00

BT40 facemill holder also called facemill arbour and facemill adaptor BT40 FMA27 Is mainly used to hold Modular Indexable Cutter with Internal hole of 16 mm any cutter can come with a 27 mm Internal thread but normally 80 mm AND 100 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 50MM,100MM,150MM,200MM,250MM,300MMRear thread for pull stud is M16 X 2.0

Mars-Tech BT40fmb 32mm Face milling ... from ₹ 1,505.00

BT40 facemill holder also called facemill arbour and facemill adaptor BT40 FMA32 Is mainly used to hold Modular Indexable Cutter with Internal hole of 16 mm any cutter can come with a 32 mm Internal thread but normally 100 mm AND 125 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 50MM,100MM,150MMRear thread for pull stud is M16 X 2.0

Mars-Tech BT40Morse taper holder MT1 ... from ₹ 1,505.00

BT40 Morse Taper holder are used to hold Tang type shanks BT40 morse taper Is mainly used to hold Tang Type Drills and Arbours Better shank taper - accurate, rigid toolholder-to-spindle mount Less tool wear and replacement - less scrap Fully ground flange and V-groove, easy on the tool changers for less spindle and changer maintenance Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundRear thread for pull stud is M16 X 2.0 This is general standard to choose morse taper size for drills (it may change with different din standard or special sizes) MT 1 IS USED FOR SMALL DRILL UPTO 14MM MT 2 IS USED FOR 14.25 MM TO 23 MMMT 3 IS USED FOR 23.5 TO 31.5 MMMT4 IS USED FOR 32TO 49.5MM3

BT50 BST HOLDER for big size boring bars rough and finish pack of 1

Mars-Tech BT50 BST HOLDER for big siz... from ₹ 9,812.00

BST adaptors are only used for rough and finish boring head which require BST type of holders , screws to fix into bst holder comes with boring head not with holder comes in different length please choose length from variations BST boring adapter for roughing and finishing boring tools

Sold out

BT50 fmb 22X250 LONG mm Face milling holder arbour pack of 1

Mars-Tech BT50 fmb 22X250 LONG mm Fac... ₹ 6,700.00

BT50 facemill holder also called facemill arbour and facemill adaptor BT50 FMA22 Is mainly used to hold Modular Indexable Cutter with Internal hole of 16 mm any cutter can come with a 22 mm Internal thread but normally 50 mm AND 63 mm Cutters are common in this range. Made from alloy steel hardened to 54 – 56rcBalanced to G6.3 at 12,000 rpmsConcentricity is less than .005 micron upto 100 Length and 0.012 upto 200 LengthAll critical tool holder surfaces precision groundGage length is 50MM,100MM,150MM,200MM,250MM,300MM

Sold out

Mars-Tech BT50 Locking device , BT50 ... ₹ 4,814.00

BT50 locking device BT50 Locking device with Vertical and Horizontal mode to tighten Nut and Pull stud made of Steel and long life. cone for taper is made of aluminium . 10 kgs of 1 pc.

Mars-Tech BT50 Pull Stud In Various D... from ₹ 361.00

BT50 Pull stud used in CNC machines for BT40 holders ISO standard name is MAS403 Pull studs are an important link between machine and tool. The requirements concerning accuracy, rigidity and reliability are very high. Pull studs of minor quality not only decrease the performance of the machine, they are even a safety risk. A breaking pull stud might cause severe damage on machine and workpiece and even injuries on persons. made of special steel for higher rigidity proper heat treated ,